From 2 to 24 ports supported, mixing FXO and FXS interfaces, as required
Support for the Asterisk®, FreeSWITCH®, Yate™, CallWeaver™, PBX/IVR projects, as well as other Open Source and proprietary PBX/Switch/IVR/VoIP gateway applications
Single synchronous PCI and PCI Express interface for all 24 FXO/FXS ports
Four RJ11 ports per Remora™ card
Dimensions: 2U Form factor: 120 mm x 55 mm for use in restricted chassis
Short 2U compatible mounting clips available for installation in 2U rack-mount servers
32 bit bus master DMA data exchanges across PCI interface at 132Mbytes/sec for minimum host processor intervention
Autosense compatibility with 5 V and 3.3 V PCI busses
Fully PCI 2.2 and PCI Express compliant, compatible with all commercially available motherboards, proper sharing of PCI interrupts
Intelligent hardware: Downloadable Field Programmable Gate Array programming with multiple operating modes. Field upgradeable so that new features can be added when they become available
Maximum operational power for PCI: 3.75 W (0.75 A @ 5 V) + 4.2 W (0.35 A @ 12 V) per FXS module For PCI Express: 2.64 W (0.8 A @ 3.3 V) + 4.2 W (0.35 A @ 12 V) per FXS module
Temperature range: 0 - 50°C
Shipped with standard RJ11-terminated cables
Get the Fax on Sangoma Hardware
With Sangoma, there is no need for a separate analog line to run your fax machine
Using T1/E1 passthrough with Sangoma analog boards, there are no clock slips, buffer overruns, or transmit underruns that cause missed lines, blank sheets, and missed pages when faxing
Sangoma A200 and A400 boards synchronize perfectly with digital T1/E1 boards and the PSTN atomic clock for error-free fax and modem passthrough and superior voice quality over T1 and E1 lines
Optional DSP Echo Canceller Daughterboard on the A200D
G.168-2002 echo cancellation in hardware
1024 taps/128ms tail per channel on all channel densities
DTMF decoding and tone recognition
Voice quality enhancement: music protection, acoustic echo control and adaptive noise reduction
No CPU load as a result of echo cancellation
Does not increase the physical size of the card, and no additional slot is required
Wiring Connections
The A200 and Remora™ cards incorporate 4-pin RJ11/4 narrow jacks, such as those used in telephone handsets
Each Sangoma A200 board is shipped with four 2 m cables terminating in a narrow RJ11/4 plug at one end and a telephone-standard RJ11/6 plug at the other
To hardwire the A200 system, you can purchase a kit of 12 RJ11/4 plugs and a crimping tool, sold separately
Linux (all versions, releases and distributions from 1.0 up)
Certifications
FCC Part 15 Class A, FCC Part 68, and EN 55022 Class A, JATE Technical certifications in Russia and Malaysia
Diagnostic Tools
WANPIPEMON®, SNMP, system logs
Architecture
The A200 consists of a Remora™ daughterboard mounted on the AFTPCI board. The Remora board has two sockets each of which can accept a FXO-2 or FXS-2 module. Each FXO-2 or FXS-2 module supports two FXO or FXS lines, respectively.
Up to five additional Remora™ daughterboards can be mounted in empty slot positions beside the A200 assembly, connected to the A200 by a backplane bus connector.
Production Quality
ISO 9002
Warranty
Lifetime warranty on parts and labour when purchased through an authorized Empowered by Sangoma Channel Partner.